COMXpress Stratix® 10 SoC

Diagrams

Tech spec

FPGA and Configuration Modules

• Stratix® 10 SX with ARMV8 (Integrated quad-core 64 bit ARM CortexA53 hard processor system up to 1.5 GHz embedded)
• MAX10 CPLD with board management control
• JTAG connector for external USB cable
• eMMC 32GBytes (HPS) / with U-boot, Linux kernel & Rootfs
• NOR Flash for quad SPI (x4) FPGA configuration mode

Memory

• 4x memory banks on board DDR4:
  • Total 56GB + ECC for Turbo version
  • Total 28GB + ECC for Lite version

Communication Interfaces

• Ethernet 10/100/1000 Base-T (HPS)
• 4x 10GbE base KR (default)
• 2x Serial SATA revision 3.0, 6Gb/s
• 4x XCVR lane connected to extension connector (DisplayPort/SDI capable)
• 3x USB2.0 HOST
• 1x USB3.0
• 1x SMB,I²C,UART
• 8 GPIOs (4 FPGA + 4 HPS)
• 2x PCI Express x16 (Gen 1, 2 or 3), end-point supported
• eSPI interface multiplexed over Intel Low Pin Count (LPC) Interface
• Network Controller Sideband Interface (NC-SI) supported (and optional)

Other resources

• Extension connector : Interfaces (4x transceivers Rx/Tx and 4xLVDS interface)
• Programmable PLL (Si5341), output clocks frequency 0.0001MHz to 750MHz
• High precision on board oscillator, clock accuracy 20MHz-0.05ppm for Precision Time Protocol (PTP) IEEE 1588

Power

• +12V primary power supply input, 120W max
• +5V standby and 3.3V RTC power supply inputs

Operating Range : 0°C to 40°C

Storage temperature Range : 0°C to 70°C

Board Dimensions

• Length : 125mm (4.92inches)
• Width : 95mm (3.74 inches)
• Height (without heatsink) :
  • 11.91mm (with 5mm Standoffs)
  • 14.91mm (with 8mm Standoffs)

Standards and compliance

• RoHS/REACH compliant
• UL certified
• ISO9001 Facility

Videos

The COMXpressSX Stratix® 10 module from REFLEX CES :

Deliverables

Board Content

• Stratix® 10 SX COMe Basic module type 7
• Delivered with a custom heatsink
• Board Support Package (Reference Manual, Design Carrier Guideline, HDL reference designs, Connectors to FPGA pin assignments)
• Kernel Linux support, U-boot bootloader and comprehensive user documentation
• JTAG adapter cable for external USB blaster probe.
• Evaluation PCIe Carrier Board available (upon request)
• 3D mechanical files (under request)

Ordering Information

• Turbo version                 :                     COMXpressSXS10L-2800T

- Intel® Stratix® 10 SoC (1SX280LN3F43E2VG)

- 2800 KLE FPGA

- On-board 56GB DDR4 + ECC :

∙  3x banks 16GB + ECC, x72bit @2400MT/s (FPGA)
∙  1x bank 8GB + ECC, x72bit @2133MT/s (used by HPS), @2400MT/s (used by FPGA)

• Lite version                 :                     COMXpressSXS10H-1100L 

- Intel® Stratix® 10 SoC (1SX110HN3F43I2VG)

- 1100 KLE FPGA

- On-board 28GB DDR4 + ECC :

∙  3x bank 8GB + ECC, x72bit @2400MT/s (FPGA)
∙  1x bank 4GB + ECC, x72bit @2133MT/s (used by HPS), @2400MT/s (used by FPGA)

COMXpress SoC with its heatsink :